5 Mistakes To Avoid While Painting Cabinets In Beaverton, ORDecember 13, 2019
The 6 Most Common Masonry Problems in Sherwood, OregonJanuary 6, 2020
Interior Painting Tigard, Oregon: How to Fix Flaking Paint in the Bathroom.
The Bathroom is the most troublesome space for many homeowners in Tigard, Oregon for keeping the paintwork intact.
Showering, drying your hair, and leaving wet towels lying around often increases the humidity in your bathroom.
As a result, paint flaking might become recurrent especially for homeowners that pay little attention to updating interior paint jobs.
In this article, we will share tips on how to fix paint flaking for your bathroom in Tigard, Oregon.
Problems Caused By Flaking Paint
Besides being unsightly, flaking paint introduces cracks that can become nests for bacteria and mold to proliferate.
Repairing flaking paint is not very complicated. However, if you suspect that a lead-based product may have been used on your walls, consult a professional for help–front to DIY.
This is important if you live in a home built before 1979.
In all other cases, here are some tips on how to fix flaking paint in the bathroom.
How to Fix Flaking Paint in the Bathroom
Step 1: Get rid of the old paint.
If you’re in a hurry, it might tempt you to paint right over old failing paint.
However, doing so will cause the unflattering paint finish, poor paint adhesion, and premature paint failure.
You can remove the old paint using a paint scraper or a putty knife.
Step 2: Sand the surface
Paint stripping alone often leaves an uneven surface behind with sharp paint film edges.
To get a smooth surface fit for painting, sand the surface using either manual sander paper or an electrical orbital sander.
After sanding, be sure to clean the resulting dust and debris off the surfaces to be painted.
Repair any cracks and uneven surfaces in the wall using a filler compound
The filling compounds are available in your local hardware stores.
If you’re applying a filling compound, allow the compound to dry completely and sand again to create a smooth surface.
Step 3: Apply the Primer
Most DIY painters tend to skip the priming stage, don’t.
One of the main reasons your bathroom paint is peeling or flaking is poor surface adhesion.
The primer improves paint color retention, coverage and adhesion, reducing the chances of peeling and flaking.
Your primer should also offer a good level of resistance against humidity damage.
Step 4: Choosing the Paint
When it comes to painting your bathroom, the paint is important in determining the performance and durability of your paint job.
The best type of paint for the bathroom is water-based latex paint.
Oil-based paint is known for being durable and can withstand scrubbing, however, it dries too slow between coats, requires mineral spirits to clean up and releases high levels of VOCs (volatile organic compounds).
An oil-based pant may also yellow over time, particularly in tight areas that receive low light.
Many formulations of latex paint today offer improved moisture resistance and durability.
Be sure to ask for washable latex paint.
Another important factor to consider in the paint finish.
The best paint finish for your bathroom is gloss or semi-gloss paint.
Both offer a good level of moisture resistance and desirable shine to your bathroom.
Step 5: Painting
Being a tight space with all the nooks and crannies, painting the bathroom can be challenging.
Start by applying the painters’ tape to all the edges you don’t want to paint.
And protect other areas including the floors using painter’s canvas.
When panting, use a sash brush that has a tapered tip.
Apply the paint uniformly, and wait for it to, dry completely before using your bathroom.
The Bottom Line
I hope the above tips provide some direction on how to repaint a bathroom with flaking paint.
Painting a bathroom is a challenging task, and it’s easy to get paint on areas and fixtures you didn’t intend to paint.
If you don’t have the right painting tools, skills, and experience, we propose that you consult a painting contractor in Tigard, Oregon like Maller Painting Company.
We have years of interior residential painting experience serving the areas of Beaverton, Sherwood, and Tigard, Oregon.
To give us a try, book a FREE estimate below or call us on (503) 410-6366 if you have any questions.
You may also like:
Kevin began painting houses with his father’s company, C&K Painting, in 1996. His father taught him how to use a brush, roller, and caulk and clean a brush properly. He then worked for several other paint companies, where he learned how to spray oils, lacquers, and all water-based finishes. In 2012, after 15 years of experience, he decided to get licensed and start the Maller Painting Company. His team has focused on providing the best re-painting services to our residential clients in the Beaverton area.